Control Arm Bushings with Fitting Position Front and Rear, Rear

A control arm bushing is the pivot connecting the arm to the chassis or subframe. It has to let the arm swing freely as the suspension travels while holding it precisely in place against everything else the road throws at it.

Control arm bushings are the most consequential bushings on any car, and when one goes you feel it everywhere. They are also among the most replaced, which is why worn control arm bushings turn up on almost every high mileage car.

What a Control Arm Bushing Actually Controls

The control arm is a lever, and that is the key to why a single bushing matters more than its size suggests.

The arm pivots on bushings at the chassis end and carries the wheel at the other, so any deflection at the pivot gets multiplied by the length of the arm before it reaches the tire. A millimeter of give where the bushing sits becomes considerably more than a millimeter of unwanted movement at the contact patch, and because most arms use two bushings, both giving at once, the effect compounds.

What that movement does is change your alignment while you drive. Under braking the wheel is pushed rearward, under cornering it is loaded sideways, and each input shifts camber, caster or toe by however much the bushing allows. The alignment shop measured your angles with the car standing still, which is why a car can read perfectly on the rack and still tramline, wander and eat the inside edge of a tire.

Factory rubber allows more of that than most people realize even when new, because it is chosen for quietness rather than control. Once it has hardened and cracked after years of heat cycling and oil exposure, it allows a great deal more.

Upper, Lower, Front and Rear

Getting the position right matters more than anything else when you order, and the naming is straightforward once you know the pattern.

The first split is upper or lower. A double wishbone setup has arms at both levels, so an upper control arm bushing and a lower control arm bushing are entirely different parts on the same car. A strut suspension usually has only the lower, which means the front lower control arm does all the positioning work and its bushings take the heaviest loads of the set.

From there the bushings are identified by where they sit on the arm, normally inner or outer, and on arms with two inner pivots they separate into forward and rearward. Add front or rear of the vehicle and you have the full description, so a front control arm bushing and a rear control arm bushing are not interchangeable.

This matters because the two inner bushings on the same arm are frequently different sizes and different hardnesses, with the rearward one often larger and softer since it absorbs fore and aft impact while the forward one handles lateral location. Ordering the wrong one of a pair is the most common mistake made with these parts, and a control arm bushing diagram for your specific car is worth looking at before you commit.

Depending on the shape of the arm you will also see these listed as A-arm bushings or wishbone bushings. Same part, same job.

Symptoms of a Bad Control Arm Bushing

• A dull clunk or thud from the front over bumps, driveways and speed bumps
• A single knock when taking up drive, shifting, or lifting off the brake
• Steering that feels vague and wanders, needing constant correction to hold a lane
• The car pulling to one side under braking
• Shudder or vibration through the wheel when braking from speed
• Uneven tire wear, most often on the inside edge
• An alignment that will not hold spec between services
• Visible cracking, splitting, bulging or separation in the bushing material
• Grease or debris packed into a split that has opened up

Control arm bushing noise has a recognizable character. It is a dull thud rather than a sharp rattle, it shows up at low speed over bumps and driveways, and it gets worse under braking. A sway bar link is a lighter, faster rattle. A ball joint knocks when the wheel is turned and loaded rather than when the suspension moves vertically.

How to Tell If Yours Are Bad

Checking takes a few minutes and settles it properly.

With the car safely supported and the suspension unloaded, work a pry bar between the arm and its mount and look for movement at the bushing rather than flex in the arm itself. Any visible shift means it is done.

Then look at the material. Rubber bushings are bonded to a metal outer sleeve, and as the rubber hardens that bond fails. You are looking for cracking across the face, a visible gap where the rubber has pulled away from the outer, material squeezed out past the edge of the housing, or an arm sitting off center in its mount rather than square.

A broken control arm bushing is usually obvious once you are under there. A worn control arm bushing that still looks reasonable is the one the pry bar finds.

How Long Can You Drive on Them?

A fair question, and the answer depends on how far gone they are.

Slightly worn bushings are not an emergency. You will lose steering precision and wear tires faster than you should, but the car stays controllable and you have time to plan the repair.

Badly worn bushings are a different situation. Once the arm can move meaningfully at its mounts, your alignment changes every time you brake or turn, so the car is least predictable at exactly the moment you need it to behave. The wear also spreads, since an arm that is moving loads the ball joint, the tires and eventually the mount itself, which turns an inexpensive job into a much larger one.

A bushing that has failed outright, where material is missing or the arm is contacting metal, should be dealt with immediately rather than at the next service.

Standard, Double Offset and Anti Lift

Most positions are offered as a direct replacement that restores the geometry the car left the factory with, and for a stock car with worn bushings that is exactly what you want.

Double offset versions have the bore moved off center, so installing them shifts the arm pivot and changes camber or caster by a degree or two. They exist for cars that have run out of factory adjustment, either because ride height has changed or because you want a performance alignment the car was never set up to allow. Because they are directional, they can also correct one side differently from the other, which is the only practical fix for a car that pulls with tires and pressures ruled out.

Caster and anti lift kits go further. Adding positive caster sharpens steering feel and straight line stability, while the anti lift geometry resists the front end rising under power and diving under brakes, which keeps the tires loaded more consistently through a corner. On a turbocharged front drive or all wheel drive car, that combination is one of the most noticeable handling changes available for the money.

What Replacement Costs

Control arm bushing replacement cost is mostly labor, and the bushings are the cheap part of this job, and understanding why is how you spend less on it.

Nearly every control arm bushing requires the arm off the car and the old bushing pressed out, and that work is identical whether you replace one bushing or every bushing on the arm. Pay for a teardown, press work and an alignment today for a single position, then pay for all three again next year for the one beside it, and the labor has cost you far more than the parts ever did.

Doing both bushings on an arm at once, and ideally both sides, is the straightforward way to avoid that. The same logic makes control arm bushing replacement almost free in labor terms if the arm is already coming off for a ball joint, a lowering kit or any other suspension work.

When you are comparing shop quotes, the numbers that actually move the total are how many positions are being done, whether the arms have to come off, and whether an alignment is included.

Pressing Them In and Out

A hydraulic press, or a dedicated control arm bushing tool, is the right way to do this, and a correct diameter control arm bushing press protects the arm eye, because the old bushing has to come out and the new one has to go in square without damaging the arm eye. Improvising with sockets, bearing shells or a hammer is how arms get ruined, and an arm costs considerably more than the tool would have.

Look at the eye once the old bushing is out, since a bore that has worn oval will never hold a new bushing properly and means the arm itself needs replacing.

Install the crush tubes and sleeves supplied with the kit, because the tube is what carries clamping load from the bolt and a bushing fitted without one gets crushed the moment the fastener is torqued.

Grease on assembly with a lubricant made for polyurethane. Silicone and PTFE based greases are correct, while ordinary lithium and petroleum based greases can degrade the material over time.

Watch orientation carefully on any double offset bushing, since one installed backwards moves the angle the wrong way and leaves you further out than when you started.

Torque everything with the car on its wheels at ride height rather than hanging at full droop, because whatever position a bushing is clamped in becomes its neutral position, and one tightened at droop will spend its whole life twisted and bind from the first mile. More new bushings are ruined by this than by anything else and it costs nothing to get right.

Finish with an alignment, since replacing these changes camber and toe immediately.

Find Control Arm Bushings for Your Vehicle

Worn arm, not just worn bushings? Whiteline's control arm kits get you sorted, and the full bushings lineup covers every other pivot.

Select your vehicle to see every control arm bushing position available for it, in standard, double offset and anti lift specifications, or search by bushing size if you are building something the fitment guide does not cover. Every Whiteline component is backed by our warranty, a fitment guarantee and 60 day returns.