Under Australia’s national modification guidelines, most cars can be lowered without engineering certification if the total height change is no more than 50mm, ground clearance stays at 100mm or more, and the change uses no more than one third of the original suspension travel. Rules vary between states, so always check with your local roads authority.
Lowering a car is one of the most popular modifications in Australia, and done properly it’s perfectly legal. The trick is knowing where the limits sit before you buy springs, because a car that’s too low can be defected, fined or knocked back at inspection. Here’s how the rules generally work, and how our lowering springs are designed to keep street cars comfortably inside them.
This is general information only and not legal advice. Requirements differ between states and territories, so confirm the current rules with your state roads authority or a licensed vehicle certifier.
What are the national rules for lowering a car?
Australia’s light vehicle modification guidelines, commonly referred to as VSB 14 or the National Code of Practice, set out what can be changed without engineering sign-off. For suspension, the key points are:
• The total change in ride height from all modifications should not exceed 50mm without certification
• Lowering should use no more than one third of the original suspension travel
• Minimum ground clearance of 100mm must be maintained
States adopt these guidelines with their own variations, so the exact wording and enforcement differ.


What does 100mm ground clearance actually mean?
Ground clearance is measured from the road to the lowest point of the car, excluding the wheels, tyres and mud flaps, generally within a set distance either side of each axle. In practice, that’s often the exhaust, a crossmember or a front spoiler lip. A simple check some police use is a 100mm block of timber slid under the car.
Remember that clearance changes with load. A car that just clears 100mm empty may dip below it with four adults on board, so leave some margin.
How much drop do Whiteline lowering springs give?
Our drops are engineered for each platform and kept modest. Typical examples include around 30mm front and rear for the Ford Fiesta WS, WT and WZ, around 20mm for the 10th and 11th generation Honda Civic, and around 35mm front and 30mm rear for the Ford Mustang S550 GT without MagneRide. These figures sit within the 50mm national guideline for total height change, although you’ll still need to confirm ground clearance on your own car, especially if you’ve fitted body kits or lowered exhaust parts.
When do you need engineering certification?
You’ll generally need a certifier if the total height change exceeds 50mm, ground clearance drops below 100mm, the suspension configuration is changed, or mounting points are modified. Air suspension, coil-to-leaf conversions and fabricated parts often fall into this category. Some states also have specific rules for adjustable or air suspension systems.
Lowering rules at a glance
|
Rule |
General national guideline |
Why it matters |
|
Total height change |
Up to 50mm without certification |
Keeps geometry and safety in range |
|
Suspension travel |
No more than one third of original travel used |
Retains bump absorption |
|
Ground clearance |
Minimum 100mm |
Avoids scraping, a common defect point |
|
Cut springs |
Not acceptable |
Unsafe, unpredictable rate and seating |
|
Certification |
Needed beyond these limits |
Engineering sign-off required |
Is cutting springs legal?
No, cutting factory springs can leave them loose in their seats, change the rate unpredictably and leave the car sitting on its bump stops. It’s widely treated as unroadworthy, and it’s genuinely unsafe. Engineered lowering springs give a predictable, controlled drop without these risks.
Other things to check after lowering
Make sure tyres don’t contact the guards or suspension at full lock or on compression, especially with wider wheels. Headlight aim can change on some cars, so have it checked. Tell your insurer about the modification. And book a wheel alignment, because lowering changes camber and toe.
FAQs
Looking for more information about legally lowering your car in Australia? Below we answer the most commonly asked questions
How low can I legally lower my car in Australia?
Is 100mm ground clearance the legal minimum?
Do I need an engineering certificate for lowering springs?
Are Whiteline lowering springs legal?
Can I get fined for a car that’s too low?
Do I need to tell my insurer about lowering springs?
Lower your car properly with our engineered lowering springs, designed around modest, platform-specific drops.
