Suspension Arms with Fitting Position Rear Axle

Suspension arms are what hold your wheels where the alignment says they should be. Springs carry the weight and dampers control the movement, but the arms decide the geometry, and geometry is what puts the tyre on the road at the angle it was designed to work at.

The range covers control arms, camber arms, toe arms, trailing arms, lateral links, radius arms and panhard rods, in fixed and adjustable forms.

Every Arm Controls One Thing

Arms get named after the job they do, which makes the range easier to navigate once you know what you are looking at.

A control arm is the general term for the link between the chassis and the hub, and on most front ends there is a lower control arm doing the main work. Where a vehicle uses upper and lower control arms together, the two share the load and give finer control over how camber changes through travel. Front lower control arms take braking and cornering load directly, which is why they wear.

A camber arm changes the lateral position of the hub, so lengthening or shortening it leans the top of the wheel in or out. A toe arm does the same job in the fore and aft plane at the rear of the hub, so it points the wheel slightly in or out. Camber arms and toe arms are usually sold as a pair because changing one moves the reading on the other.

A trailing arm runs lengthwise and holds the wheel against acceleration and braking load, while a lateral link holds it against sideways load. A radius arm does the fore and aft job on a solid axle and also controls how far the housing rotates, which means it sets caster.

A panhard rod is the odd one out. It runs across the vehicle rather than along it, and its only job is stopping the axle moving sideways underneath the body.

Why Factory Arms Run Out of Adjustment

Manufacturers build in just enough adjustment to correct production tolerances, and not a millimetre more. That is fine on a standard car sitting at standard height.

Change the ride height in either direction and the arms swing through a different part of their arc. Camber goes negative on a lowered car and positive on a raised one, caster washes off as the geometry rotates, and toe follows both. On plenty of platforms the car ends up outside specification with nothing worn at all, and the alignment shop has nothing left to adjust.

That is not a fault the aligner can fix. The numbers are out of range and something has to physically move a mounting point before the machine has anything to work with.

Worn bushings do the same thing a different way. Even when the static numbers read correctly, a soft bush lets the arm deflect under load, so your geometry is only right while the car is standing still. That is why a car can measure perfectly on the rack and still tramline, wander and chew tyres.

Adjustable Arms and What They Give You

An adjustable arm lets the length be set, which hands the aligner range that did not previously exist.

Adjustable camber arms and toe arms are what bring a lowered car back into specification, and they let you go past factory settings deliberately if you want a performance alignment with more negative camber than standard. Adjustable upper control arms recover caster and camber on a raised vehicle where the factory arm has nothing left to give. An adjustable panhard rod re-centres an axle that has shifted sideways after a lift.

Because each side adjusts independently, they also fix problems a symmetrical correction cannot. A car that has settled unevenly, or one that pulls to one side with tyres and pressures ruled out, can be corrected side to side rather than split down the middle.

Fixed offset arms are the alternative. The correction is built into the shape of the arm, so it is right the moment it is bolted in and nothing can move or work loose. On a vehicle at a known ride height that reliability is often the better choice.

Panhard Rods and Lateral Axle Location

On a solid axle, the panhard rod is the only thing stopping the axle sliding sideways under the body, and there are just two bushings holding that location.

When they soften, the axle gains lateral movement. The back end shuffles sideways over mid corner bumps, the vehicle feels like it is moving underneath you on rough roads, and it wanders at speed in a way nothing else explains. Fresh panhard rod bushes are one of the cheapest fixes in the whole suspension for the change they make.

Raising the vehicle is a different problem. The rod sits at a steeper angle, which pushes the axle across and holds it there, so the axle sits off centre in the wheel arches with more tyre clearance on one side than the other. Bushings will not bring that back because the rod is now the wrong length for the new ride height. An adjustable panhard rod is what re-centres it.

Upper Control Arms on a Raised Vehicle

Lifting a 4WD or pick-up changes camber and caster immediately, and factory upper control arms have very little adjustment to recover either.

The symptoms are predictable. Steering that wanders and needs constant correction, tyres wearing on one edge, and an alignment the shop cannot bring into spec no matter how long they spend on it.

There is a second issue people miss. A factory upper ball joint is built around factory travel, so once the vehicle is raised the arm works at a steeper angle and the joint is asked to articulate further than it was designed to at full droop. It binds, tears its boot and wears out early, which is why people fit a lift and then start replacing upper ball joints regularly. Purpose built arms use a joint with the articulation to handle it.

Arms, Bushes, or Both

The right purchase depends on what has actually gone, so it is worth diagnosing before ordering.

Bushes alone make sense when the arm is straight, the mounting eyes are round, the ball joint is tight and the ride height has not changed. That is the cheapest route and it fixes the deflection without touching the geometry.

An arm is the answer when the ride height has changed and you need correction the factory never provided, when the arm is bent or corroded, when a mounting eye has worn oval and will no longer hold a bush, or when the ball joint is integral and has failed.

The arm has to come off the vehicle for either job, so once more than one thing is due, a complete arm frequently works out better value than rebuilding.

Fitting and Alignment

Most arms bolt into factory mounting locations and arrive assembled, so this is a spanner job rather than a press job.

Support the vehicle properly and take the load off the suspension before separating a ball joint, since a joint under spring load releases suddenly. Use a proper separator rather than a hammer.

Fit both sides. A corrected arm working against a factory one gives you two different geometries and an alignment nobody can balance.

Torque with the vehicle on its wheels at ride height rather than hanging at full droop, because whatever position a bush is clamped in becomes its neutral position and one tightened at droop binds from the first kilometre.

Book the wheel alignment for the same visit. The entire point of an adjustable or corrected arm is to give the aligner range, so driving away unaligned wastes the exercise. Set adjustable arms roughly beforehand and let the aligner make the final call with the machine reading the numbers.

Find Suspension Arms for Your Vehicle

The range also covers control arm and radius arm kits and suspension arm service kits, and sits within our wider suspension parts line-up.

Select your vehicle to see the control arms, camber and toe arms, trailing arms, lateral links, radius arms and panhard rods available for it, and check each listing for the adjustment range it offers. Every Whiteline component is backed by our warranty, a fitment guarantee and 30 day returns.