Suspension Bushes with Fitting Position Rear Axle

A suspension bush is the flexible sleeve sitting between two metal suspension parts. It lets the joint pivot, keeps metal off metal, and controls how far the component is allowed to move. Nearly every pivot point on a car has one, which is why a single vehicle carries dozens.

Bushes are what hold your alignment in place while you drive. When they go soft, the geometry moves with every bump and every corner, and no amount of work elsewhere will fix it.

What a Bush Actually Controls

Springs carry the weight and dampers control the movement. The bushes decide where everything is pointed while that happens.

Take a control arm. It pivots on bushes at the chassis end and carries the wheel at the other, so under brakes the wheel is being pushed backward and through a corner it is being loaded sideways. The only thing resisting either is the bush at each pivot, and whatever deflection it allows becomes a change in camber, caster or toe at the tyre.

Because the arm is a lever, that deflection is multiplied by the time it reaches the road. A millimetre of give at the pivot becomes considerably more than a millimetre of unwanted movement at the contact patch, and with two bushes on most arms giving at once, the effect compounds.

This is why a car can measure perfectly on an alignment rack and still tramline, wander and chew the inside edge of a tyre. The shop measured it standing still, and standing still there is nothing wrong.

Where Bushes Sit on Your Car

Almost every pivot and mounting point has one, and each does a different job.

Control arm bushes stabilise the arms so the geometry holds under load, and front lower control arm bushes take the heaviest of it since that arm does the most work. Upper control arm bushes do the same at the top of the hub where a vehicle uses one.

Anti roll bar bushes locate the bar to the chassis so it can twist rather than move, while anti roll bar link bushings hold the ends tight so the load actually reaches the bar.

Leaf spring bushes and shackle bushes stabilise the movement of a solid rear axle, and worn ones let the axle shift enough to steer the back of the vehicle on its own. Radius arm bushes and caster bushes control axle rotation and therefore caster on a solid front axle. Trailing arm bushes handle acceleration and braking load at the rear, and panhard rod bushes are the only thing stopping a live axle moving sideways.

Beyond those there are shock absorber bushes at both mounts, differential and subframe mounts, strut rod and steering rack bushings, and the smaller positions nobody thinks about until something rattles.

Polyurethane Bushes Against Factory Rubber

Factory bushes are rubber because rubber is quiet and cheap to produce at volume, and it absorbs small road inputs before they reach the cabin. That is genuinely useful on a standard car.

What you pay for it is deflection and lifespan. Rubber compresses under load and never fully returns, it dries out and cracks through heat cycling and UV, and oil contamination finishes whatever is left. It is also specified for a standard car on standard tyres carrying standard loads, so the moment you lower it, raise it, add weight, tow with it or fit grippier tyres, the rubber suspension bush is working outside anything it was designed for.

The polyurethane versus rubber bushings question comes up constantly, and the answer is that polyurethane holds its shape where rubber gives up.

• Less deflection, so the alignment stays where the shop set it under load instead of drifting
• Far longer service life, since polyurethane does not perish, crack or dry rot the way rubber does
• Resistance to the oil, grease, ozone and weathering that live under every car
• Steering response you can predict, because the amount of movement does not change with load
• Load capacity for towing, touring and modified setups the original rubber was never rated for

The objection people raise is harshness, and it deserves a straight answer. Bush design and hardness decide ride quality far more than the material itself, and our range includes formulations tuned for daily driving as well as firmer options built for track use. Where a kit is aggressive enough to add noise or vibration, the listing says so.

What Grease to Use on Polyurethane Bushings

This one matters and it is the question most often asked after fitting.

Polyurethane bushes work by sliding on the crush tube rather than twisting the way a bonded rubber bush does, so they rely on a film of grease between the bush and the tube. Without it the bush wears its way to a fit and starts squeaking, which is the single most common complaint after a poly bush install and is almost always an assembly problem rather than a product one.

Use a grease formulated for polyurethane. Silicone based and PTFE greases are the right choice, since they stay put and will not attack the material. Ordinary lithium and petroleum based greases are what to avoid, because over time they can degrade polyurethane rather than protect it.

Grease the bore and the crush tube on assembly, not just one of them, and where a bush is designed to be serviced with a nipple, top it up at each service.

Signs of Worn Suspension Bushes

• Clunking, knocking or squeaking from the suspension over bumps and driveways
• Steering that feels vague and wanders, needing constant correction
• More body roll in corners with a floaty, unsettled feel
• Uneven tyre wear, usually concentrated on one edge
• An alignment that will not hold spec between services
• The car pulling to one side under braking
• Visible cracking, splitting, perishing or material squeezed out of a bush
• Everything getting noticeably worse under load, while towing, or off road

If you are chasing a noise nobody can find, worn suspension bushes are worth checking before anything else. They fail quietly and gradually, which is exactly why they get overlooked.

Front, Rear or the Whole Car

Kits are offered at several depths and the right one depends on what you are chasing.

Single position kits target one joint, which suits a diagnosed fault where the rest of the suspension is genuinely sound. Front suspension bushes and rear suspension bushes are also grouped by end of the car, covering the positions that matter most for how it drives without dismantling every mounting point.

Complete vehicle kits cover every position, which suits an older car still on original rubber or a build where you want the suspension sorted properly and then forgotten.

Bushes are matched to the housing they sit in rather than the vehicle alone, so if you are working on something modified or unusual, searching suspension bushes by size will find a part when a vehicle lookup will not.

What Replacement Costs

The bushes themselves are inexpensive. Getting to them is not.

Almost every position needs the arm or component off the car and the old bush pressed out, and that work takes the same time whether you replace one bush or every bush on that corner. Pay for the teardown, the press work and an alignment today for a single position, then pay for all three again next year, and the labour has cost you far more than the parts ever did.

That is the argument for doing a whole corner, or a whole end of the car, in one go. It is also why fitting bushes during any other suspension work costs almost nothing extra in labour.

If you are comparing quotes, the variables that move the number are how many positions are being done, whether components have to come off the car, and whether an alignment is included.

Pressing and Torque at Ride Height

Most positions need a press, and a correct diameter press tool is what keeps the mounting eye intact. A damaged eye cannot be repaired and costs far more than the tool, so improvising with sockets or old bearing shells is a false economy.

Check the eye while the old bush is out. A bore worn oval will not hold a new bush and means that component needs replacing rather than rebushing.

Fit the crush tubes and sleeves supplied, because the tube carries clamping load from the bolt and a bush fitted without one gets crushed the moment the fastener is torqued.

Torque with the car on its wheels at ride height rather than hanging at full droop. Whatever position a bush is clamped in becomes its neutral position, so one tightened at droop spends its life twisted and binds from the first kilometre. This is the most common mistake made on bush work by a wide margin.

Finish with a wheel alignment on anything affecting wheel position, since fresh bushes change where everything sits and the old settings no longer apply.

Find Suspension Bushes for Your Vehicle

Popular lines include alignment bushes for dialling in camber and caster, complete bushing kits for full rebuilds and differential bushes for cutting wheel hop. Explore the rest of the suspension parts range for arms, anti roll bars and springs.

Select your vehicle to see every polyurethane bush position available for it, from a single kit through to a complete vehicle kit, or search by bush size if you are working on something the fitment guide does not cover. Every Whiteline component is backed by our warranty, a fitment guarantee and 30 day returns.