Lower Control Arms with Fitting Position Front Axle

The lower control arm is the link running from the chassis or subframe out to the bottom of the hub. It pivots on bushes at the inner end, carries the lower ball joint at the outer end, and on most cars it is the arm doing the heaviest work.

It is also the lowest and most exposed part of the front suspension, which is why it sees more abuse than anything else down there.

The Arm That Does the Most Work

On a strut suspension there is one lower arm per side and that is the lot. The strut locates the top of the hub, so everything else falls to the front lower control arm: holding the wheel in position, resisting braking and cornering load, and providing the pivot the hub steers around. There is no upper arm to share any of it.

On a double wishbone layout the load is split between two arms, but the spring usually sits on the lower one anyway, so it carries vehicle weight on top of everything else.

Either way the lower arm is a lever, and whatever movement it allows at the inner pivots gets multiplied by the time it reaches the tyre. A small amount of give at the bush becomes a much larger amount of movement at the contact patch, which is why a tired lower arm shows up as vague steering and uneven tyre wear well before anything looks obviously broken.

Rear lower control arms do a related job at the back, setting camber and holding the hub against cornering load.

Split Bushes and What They Cost You

The most common failure on a lower control arm is the inner bush, and the most common visible sign is a split.

Factory rubber is chosen to be quiet rather than firm, so it deflects under load even when new. Years of heat cycling, oil contamination and load leave it hardened and cracked, and eventually the rubber splits away from its outer sleeve. Once that happens the arm can move meaningfully at the pivot, and your camber and toe are changing every time you brake or turn in.

What you feel is a car that wanders and needs constant correction, that pulls one way under braking, and that goes through the inner edge of a front tyre far quicker than it should. What the alignment shop sees is a car that measures correctly on the rack, because the vehicle is standing still and the load causing the movement is not there.

Whiteline synthetic elastomer bushes hold their shape where rubber deflects, so the arm stays where the alignment put it under load rather than only when parked.

Complete Arm or Just the Bushes

Both are legitimate and the right answer depends on what has actually gone.

Lower control arm bushes on their own make sense when the arm is straight, the mounting eyes are round, the ball joint is still tight and ride height has not changed. Fresh lower arm bushes will remove the deflection and stop the geometry moving while you drive, and that is the cheapest route by a distance.

A complete arm is the better purchase when both ends are due, when the arm is bent or corroded, when a mounting eye has worn oval and will no longer hold a bush, or when the ball joint is pressed into the arm and has failed.

There is also a practical argument worth being honest about. Removing and replacing bushes and ball joints in a suspension arm takes time, a press and the right tooling, and the risk of damaging the arm eye is real. A complete arm arrives with the bushes and, where the design uses one, the ball joint already fitted, which turns a press job into a spanner job. For a lot of people that alone justifies the difference.

The Lower Ball Joint

On most cars the lower ball joint is the loaded joint, carrying vehicle weight while the hub steers and the suspension travels.

Its life is decided by the boot rather than the mileage. While the boot is intact the grease stays in and the joint wears slowly. Once it splits, water and grit get into the socket and the grease washes out, so a lower control arm ball joint that still feels tight can be much further through its life than it appears.

How the joint is attached decides what you buy. Where it bolts in, it comes out on its own. Where it is pressed or riveted into the arm, replacing it means pressing or fitting a complete assembly, and on plenty of vehicles the assembly is the sensible route.

A lower ball joint with genuine play is a safety item rather than a comfort one, since it is what holds the hub to the car. That one does not wait for the next service.

Adjustable and Alloy Options

Beyond direct replacements, some applications are offered with adjustment built in.

Adjustable caster and camber versions give the aligner range the factory never provided, which is what a lowered car needs once the standard adjustment has been used up. Alloy arms reduce unsprung weight and add rigidity where the vehicle is being driven hard.

Check the listing for which version you are looking at, since fitting a correction arm to a standard height car will move the alignment in a direction you did not ask for.

Signs Your Lower Control Arms Need Attention

• A dull clunk or thud from the front over bumps, driveways and speed humps
• Clunking that appears when the wheel is turned and loaded, which points at the ball joint
• Steering that feels vague and wanders, needing constant correction
• The car pulling to one side under braking
• Shudder or vibration through the wheel when braking from speed
• Uneven tyre wear, most often on the inside edge
• An alignment that will not hold spec, or one the shop cannot reach at all
• Front lower control arm bushes visibly split, cracked or separated from their sleeve
• A torn ball joint boot, or grease thrown around the inside of the wheel
• Visible bending or heavy corrosion after a kerb strike or pothole

A bent arm is worth checking for specifically if the car has hit something hard and the alignment has never been right since. A few millimetres of deflection looks like nothing and changes where the wheel sits entirely.

What Replacement Costs

The parts are rarely what drives the number on a lower control arm job. Labour is.

The arm has to come off the car whichever route you take, and a wheel alignment afterwards is mandatory rather than optional since replacing an arm changes camber and toe immediately. Those two are fixed costs regardless of what you fit between them.

That is why doing both inner bushes at once, and doing both sides together, is where the saving actually comes from. It is also why replacing bushes during any other front end work costs very little extra in labour.

If you are comparing quotes, the three variables that explain almost all of the difference are how many arms are being done, whether complete arms or bush and ball joint repairs are being quoted, and whether the alignment is included in the price.

Fitting and Alignment

A complete arm bolts into the factory mounting locations and arrives assembled, which is the main reason to buy the arm rather than the pieces.

Support the car on stands and take the spring load off before separating the ball joint, because a joint under load releases suddenly. Use a proper separator rather than a hammer, since hammering damages the hub bore and the stud threads.

Where you are pressing bushes instead, use a correct diameter press tool. The mounting eye is the expensive part and improvising with sockets is how arms get ruined.

Do both sides where the wear is age related, because a new arm working against a tired one leaves the front end behaving differently left to right.

Torque the inner fasteners with the car on its wheels at ride height rather than hanging at full droop. Whatever position a bush is clamped in becomes its neutral position, so an arm torqued at droop spends its life twisted and binds from the first kilometre.

Book the alignment for the same visit.

Find Lower Control Arms for Your Vehicle

Replacing one side only? Individual lower control arms are listed separately within our control arms range.

Select your vehicle to see the arms, arm kits and bush kits available for it, and check each listing for the side it suits and whether a ball joint is included. Every Whiteline component is backed by our warranty, a fitment guarantee and 60 day returns.