Control Arm Bushes

A control arm bush is the pivot connecting the arm to the chassis or subframe. It has to let the arm swing freely as the suspension travels while holding it precisely in place against everything else the road applies.

Control arm bushings are the most replaced bushes on any car, partly because they carry more load than almost any other position and partly because when they go, you feel it everywhere.

The Bush That Decides Your Alignment

The control arm is a lever, and that is the key to why these matter more than their size suggests.

The arm pivots on bushes at the chassis end and carries the wheel at the other, so any deflection at the pivot gets multiplied by the length of the arm before it reaches the tyre. A millimetre of give at the bush becomes considerably more than a millimetre of unwanted movement at the contact patch, and because most arms use two bushes, both giving at once, the effect compounds.

What that movement does is change your alignment while you drive. Under brakes the wheel is pushed backward, through a corner it is loaded sideways, and each input shifts camber, caster or toe by however much the bush allows. The alignment shop measured your angles with the car standing still, which is why a car can read perfectly on the rack and still tramline, wander and eat the inside edge of a tyre.

Factory rubber allows more of that movement than most people realise even when new, because it is chosen for quietness rather than control. Once it has hardened and cracked after years of heat cycling and oil exposure, it allows a great deal more.

Split Bushes and What to Look For

The most visible failure on a control arm bush is a split, and it is worth knowing what you are looking at.

Rubber bushes are bonded to a metal outer sleeve. As the material hardens with age the bond fails, and the rubber begins to separate and tear away from the sleeve. Once that happens the arm can move meaningfully at the pivot, and it will not get better.

Front lower control arm bushes are where you see it most, because that arm does the heaviest work and the lower arm bushes take the brunt of everything the road applies. Look for cracking across the face, material squeezed out past the edge of the housing, a visible gap where the rubber has pulled away from the outer, or the arm sitting off centre in its mount rather than square.

A bush can also be finished without an obvious split. If you can lever the arm against its mount and see movement at the pivot rather than flex in the arm itself, that bush has had it regardless of how it looks.

Which Position You Need

Control arm bushes are described by position, and getting it right matters more than anything else when ordering.

The first split is upper or lower, since a double wishbone layout has arms at both levels while a strut suspension usually has only the lower. Upper control arm bushings are a different part to lower control arm bushings even on the same car.

From there they are identified by where they sit on the arm, normally inner or outer, and on arms with two inner pivots they separate into forward and rearward. Add front or rear of the vehicle and you have the full description, so a front lower control arm bush and a rear lower control arm bush are entirely different parts.

This matters because the two inner bushes on the same arm are frequently different sizes and different hardnesses, with the rearward one often larger and softer because it absorbs fore and aft impact while the forward one handles lateral location. Ordering the wrong one of a pair is the most common mistake people make.

Bushes are also matched to the housing rather than the vehicle alone, so if you are working on something modified, measuring the arm eye and searching by dimension will find a part when a vehicle lookup will not.

Polyurethane Against Factory Rubber

Rubber is quiet and cheap to mould at volume, and it absorbs small road inputs before they reach the cabin. That is genuinely useful on a standard car.

What you pay for it is deflection and lifespan. Rubber compresses under load and never fully returns, it perishes through heat cycling and UV, and oil contamination finishes whatever is left. It is also specified for a standard car on standard tyres carrying standard loads, so the moment you lower it, add power or fit grippier tyres it is working outside what it was designed for.

Polyurethane control arm bushings hold their shape where rubber gives up. The arm stays where the alignment put it under load rather than only when parked, which is why the difference is most obvious under brakes and through a corner rather than over bumps.

They also last considerably longer, resisting the oil, grease, ozone and weathering that live under every car.

Signs Your Control Arm Bushes Are Worn

• A dull clunk or thud from the front over bumps, driveways and speed humps
• A single knock when taking up drive, changing gear or lifting off the brake
• Steering that feels vague and wanders, needing constant correction
• The car pulling to one side under braking
• Shudder or vibration through the wheel when braking from speed
• Uneven tyre wear, most often on the inside edge
• An alignment that will not hold spec between services
• Visible cracking, splitting or separation in the control arm bushing material
• Movement at the pivot when the arm is levered against its mount

What Replacement Costs

The bushes are the cheap part of this job, and understanding why is how you spend less on it.

Nearly every control arm bushing needs the arm off the car and the old bush pressed out, and that work is identical whether you replace one bush or every bush on the arm. Pay for a teardown, press work and an alignment today for a single position, then pay for all three again next year for the one beside it, and the labour has cost far more than the parts ever did.

Doing both bushes on an arm at once, and ideally both sides, is the straightforward way to avoid that. The same logic makes bushes almost free in labour terms if the arm is already coming off for a ball joint, a lowering kit or any other suspension work.

When you are comparing quotes, the numbers that actually move the total are how many positions are being done, whether the arms have to come off, and whether an alignment is included.

Pressing, Greasing and Torque at Ride Height

Most positions need a press, and a correct diameter press tool is what keeps the arm eye intact. Improvising with sockets or old bearing shells is how arms get ruined, and an arm costs considerably more than the tool would have.

Check the eye once the old bush is out. A bore worn oval will never hold a new bush properly and means the arm itself needs replacing rather than rebushing.

Fit the crush tubes and sleeves supplied, because the tube carries clamping load from the bolt and a bush fitted without one gets crushed the moment the fastener is torqued.

Grease on assembly with a lubricant made for polyurethane. Silicone and PTFE based greases are correct, while ordinary lithium and petroleum based greases can degrade the material over time. Grease the bore and the crush tube, not just one of them, since a dry bush wears its way to a fit and squeaks.

Torque with the car on its wheels at ride height rather than hanging at full droop. Whatever position a bush is clamped in becomes its neutral position, so one tightened at droop spends its life twisted and binds from the first kilometre. More new bushes are ruined by this than by anything else and it costs nothing to get right.

Finish with a wheel alignment, since removing play changes camber and toe immediately.

Find Control Arm Bushes for Your Vehicle

Control arm bushes are the biggest line in our suspension bushes range.

Select your vehicle to see every control arm bush position available for it, or search by bush size if you are working on something the fitment guide does not cover. Every Whiteline component is backed by our warranty, a fitment guarantee and 60 day returns.