Upper Control Arms
IMPROVE GRIP, HANDLING & PERFORMANCE.
The upper control arm holds the top of the hub while the lower arm holds the bottom, and between them they set camber and caster. On a double wishbone front end it is doing a genuine share of the work rather than just going along for the ride. People end up here for two different reasons. Either the arm has worn out and needs replacing, or the v... Read more
The upper control arm holds the top of the hub while the lower arm holds the bottom, and between them they set camber and caster. On a double wishbone front end it is doing a genuine share of the work rather than just going along for the ride.
People end up here for two different reasons. Either the arm has worn out and needs replacing, or the vehicle has been lifted and the alignment can no longer be brought back.
Where the Upper Arm Sits in the System
On a strut suspension there is no upper control arm at all, since the strut locates the top of the hub. Where a vehicle does use one, it works with the lower arm to control how camber changes as the suspension travels, which is why the layout turns up on utes, 4WDs and performance cars.
The upper arm carries less vertical load than the lower, because the spring usually sits on the lower arm. What it does carry is the sideways and twisting load from cornering, braking and steering, all fed through a ball joint that is typically smaller than the one underneath.
That combination explains a lot. A front upper control arm can be worn out while the lower one is perfectly healthy, and the wear is usually concentrated in the joint rather than spread across the arm.
Rear upper control arms turn up on independent rear ends doing a similar job on camber and keeping the hub square under load.
Why the Ball Joint Usually Goes First
The upper ball joint is the part that fails on most of these arms, and the boot is what decides its life rather than the kilometres.
While the boot is intact the grease stays where it belongs and the joint wears slowly. Once it splits, water and grit get into the socket, the grease washes out, and an upper control arm ball joint that still feels reasonably tight can be a long way through what is left of its service life.
How the joint is attached determines what you buy. Where it is pressed or riveted into the arm it is not separately serviceable in any practical sense, so a worn joint means a new arm. Some designs allow the joint to come out on its own.
Check the boots whenever the vehicle is in the air. A torn boot is the cheapest thing to act on and the most expensive thing to ignore.
Lifting a 4WD and What It Does to Caster
Raise a ute or 4WD and the arms swing through a different part of their arc, which changes camber and caster immediately and permanently.
Caster is what you notice first. It washes off as the geometry rotates, and caster is what makes the steering settle and return to centre, so losing it gives you a vehicle that wanders at highway speed, needs constant small corrections and feels lazy turning in. Camber moves at the same time, which is what starts wearing the inside or outside edge of a new set of tyres.
Factory upper control arms have very little adjustment designed into them, and on most vehicles whatever there was has already been used before the lift went in. The alignment shop will tell you the numbers are out. They will not be able to do anything about it, because there is nothing left to adjust.
There is a second problem that gets less attention and often causes more grief. A factory upper ball joint is built around factory suspension travel, so once the vehicle is raised the arm sits at a steeper angle through its whole range and the joint is asked to articulate further than it was designed to at full droop. It binds at the extreme of travel, the boot stretches and tears, and the joint is finished shortly afterwards. That is why people fit a lift and then find themselves replacing upper ball joints regularly.
Purpose built arms address both at once, restoring the geometry while using a joint with the articulation a raised vehicle actually needs.
Fixed Offset and Adjustable
Fixed offset upper control arms have the correction built into the shape of the arm, so they are right the moment they are bolted in and nothing can move or work loose afterwards. On a vehicle sitting at a known lift height, that reliability is usually what you want.
Adjustable upper control arms let the setting be dialled in on the alignment rack and allow each side to be set differently, which matters on a vehicle that has settled unevenly or pulls to one side with tyres and pressures ruled out. They also give you room to change ride height later without buying arms again.
Check the lift range an arm was designed around. These are engineered for a band rather than for anything, and an arm built for one height fitted to a very different one moves the geometry in a direction you did not ask for.
Bushes, Ball Joint or the Whole Arm
Worth diagnosing before you order, because the cheaper answer is sometimes the right one.
Upper control arm bushes on their own make sense when the ball joint is still tight, the arm is straight and the ride height has not changed. Fresh front upper control arm bushes remove the deflection that lets the arm move under load and stop the geometry wandering while you drive. Offset camber adjustable upper control arm inner bushing kits will even give you a degree of correction without changing the arm.
The complete arm is the answer when the joint has gone as well, when the arm is bent or corroded, when a mounting eye has worn oval and will no longer hold a bush, or when you need correction the factory never provided.
There is also the practical side. Pressing bushes and ball joints out of an arm takes time, a press and the correct tooling, and the risk of damaging the arm is real. A complete arm arrives assembled with Whiteline synthetic elastomer bushes fitted, which turns a press job into a spanner job.
Signs Your Upper Control Arms Need Attention
- Clunking or knocking from the front over bumps, often worse at low speed
- A knock or shudder felt through the steering wheel
- Steering that wanders and needs constant correction, worse at highway speed
- Uneven tyre wear across one edge that keeps returning after alignment
- Play at the ball joint when the wheel is rocked with the suspension unloaded
- A split or torn ball joint boot, or grease thrown around the wheel arch
- Upper ball joints failing repeatedly since a lift was fitted
- Cracked, split or squeezed out material in the upper control arm bushes
- Caster reading low on an alignment printout with nothing worn to explain it
- An alignment the shop cannot bring into specification at all
That last one is the clearest signal there is. If the aligner has run out of range, no amount of new bushes will hand it back.
Fitting and Alignment
Upper arms bolt into the factory mounting locations and arrive assembled, so this is a remove and replace job rather than press work.
Support the vehicle and take the load off the suspension before separating the ball joint, since a joint under spring load releases suddenly. Use a proper separator rather than a hammer.
Fit both sides. A corrected arm working against a factory one gives you two different geometries and an alignment that cannot be balanced.
Torque the inner fasteners with the vehicle on its wheels at ride height rather than hanging at full droop, or the bushes sit preloaded in a position the suspension never returns to and bind from the first kilometre.
Cycle the suspension through full travel before calling it done, checking clearance against the coil or strut at both extremes, then book the wheel alignment for the same visit. The whole purpose of a corrected arm is to give the aligner range, so driving away unaligned wastes the exercise.
Find Upper Control Arms for Your Vehicle
Single-side options are under individual upper control arms, part of our wider control arms range.
Select your vehicle to see the arms and bush kits available for it, and check each listing for the correction it provides and the lift range it suits. Every Whiteline component is backed by our warranty, a fitment guarantee and 60 day returns.
54 items
- SKU: KTA240 Benefit Note: A short fall of the modern day IFS 4wd is the adjustment range provided for successful wheel alignments, this becomes even more of an issue when the vehicle is lifted by more than 1 inch. Not only does the vehicle run into camber and caster issues, but ball joint articulation and clearance issues to the coil over strut at ride and droop height. The new Whiteline offset UCA (Upper Control Arm) is an all-in-one solution for any vehicle that has been lifted between 30mm and 70mm. Providing an increase between +2.5 and +3.5 degrees of caster and up to 1.5 degrees of negative camber increase (figures quoted are based off an approximate 50mm/ 2 inch) along with greater clearance to the coil over strut and more articulation of the arm by virtue of new maintenance free GIIRO bushing technology.
Front Upper Control Arms Fixed Offset to Suit Ford Everest, Ranger PX and Mazda BT-50 UP, UR
ℹ️ Fixed offset alignment correction arms - includes ball jointGreatly increases control and confidence; the perfect, complete upgrade. Includes: 2 ArmsIn StockShips within 24hrs.Ships within 24hrs.Qty Required 1Kit Contents 2 Arms$806.55 $564.59Fully installed for $1,084.59within 2 weeksSelect Option To Show Price - SKU: KTA246 Benefit Note:
A short fall of the modern day IFS 4wd is the adjustment range provided for successful wheel alignments, this becomes even more of an issue when the vehicle is lifted by more than 1 inch. Not only does the vehicle run into camber and caster issues, but ball joint articulation and clearance issues to the coil over strut at ride and droop height. The new Whiteline offset UCA (Upper Control Arm) is an all-in-one solution for any vehicle that has been lifted between 30mm and 70mm. Providing an increase between +2.5 and +3.5 degrees of caster and up to 1.5 degrees of negative camber increase (figures quoted are based off an approximate 50mm/ 2 inch) along with greater clearance to the coil over strut and more articulation of the arm by virtue of new maintenance free GIIRO bushing technology.Front Upper Control Arms Fixed Offset to Suit Toyota Land Cruiser 200 Series
ℹ️ Fixed offset alignment correction arms - includes ball jointMaximises tyre contact with the road, improving cornering and grip; the perfect, complete upgrade. Includes: 2 ArmsIn StockShips within 24hrs.Ships within 24hrs.Qty Required 1Kit Contents 2 Arms$806.55 $564.59Fully installed for $1,084.59within 2 weeksSelect Option To Show Price - SKU: WA378L Benefit Note:
Most would agree that the time and stress to remove and replace bushings and ball joints to suspension arms can be hard to justify. Making up press tools and damaging arms are just two of the problems one can endure. Why put yourself through it when you can purchase complete arms, fitted with market leading Whiteline synthetic elastomer bushings and premium quality ball joints.Front Upper Control Arm Left to Suit Toyota HiLux 2005-on and Foton Tunland 4wd
ℹ️ Replacement and repair upgrade - includes ball jointEnhances steering response, delivering sharper handling and more predictable vehicle dynamics; the perfect, complete upgrade. Includes: 1 ArmIn StockShips within 24hrs.Ships within 24hrs.Qty Required 1Kit Contents 1 Arm$191.00 $133.71Fully installed for $463.71within 2 weeks - SKU: WA395 Benefit Note:
Most would agree that the time and stress to remove and replace bushings and ball joints to suspension arms can be hard to justify. Making up press tools and damaging arms are just two of the problems one can endure. Why put yourself through it when you can purchase complete arms, fitted with market leading Whiteline synthetic elastomer bushings and premium quality ball joints (if applicable).Front Upper Control Arms to Suit Ford Falcon FG, FGX and FPV
ℹ️ Replacement and repair upgrade - includes ball jointMaximises tyre contact with the road, improving cornering and grip; the perfect, complete upgrade. Includes: 2 ArmsIn StockShips within 24hrs.Ships within 24hrs.Qty Required 1Kit Contents 2 Arms$569.00 $398.30Fully installed for $918.30within 2 weeks - SKU: WA395L Benefit Note:
Most would agree that the time and stress to remove and replace bushings and ball joints to suspension arms can be hard to justify. Making up press tools and damaging arms are just two of the problems one can endure. Why put yourself through it when you can purchase complete arms, fitted with market leading Whiteline synthetic elastomer bushings and premium quality ball joints (if applicable).Front Upper Control Arm Left to Suit Ford Falcon FG, FGX and FPV
ℹ️ Replacement and repair upgrade - includes ball jointMaximises tyre contact with the road, improving cornering and grip; the perfect, complete upgrade. Includes: 1 ArmIn StockShips within 24hrs.Ships within 24hrs.Qty Required 1Kit Contents 1 Arm$327.00 $228.90Fully installed for $558.90within 2 weeks - SKU: KTA254 Benefit Note: A short fall of the modern day IFS 4wd is the adjustment range provided for successful wheel alignments, this becomes even more of an issue when the vehicle is lifted by more than 1 inch. Not only does the vehicle run into camber and caster issues, but ball joint articulation and clearance issues to the coil over strut at ride and droop height. The new Whiteline offset UCA (Upper Control Arm) is an all-in-one solution for any vehicle that has been lifted between 30mm and 70mm. Providing an increase between +2.5 and +3.5 degrees of caster and up to 1.5 degrees of negative camber increase (figures quoted are based off an approximate 50mm/ 2 inch) along with greater clearance to the coil over strut and more articulation of the arm by virtue of new maintenance free GIIRO bushing technology.
Front Upper Control Arms Fixed Offset to Suit Mitsubishi Challenger, Pajero Sport and Triton 4wd
ℹ️ Fixed offset alignment arms - suits QE models - includes ball jointMaximises tyre contact with the road, improving cornering and grip; the perfect, complete upgrade. Includes: 2 ArmsIn StockShips within 24hrs.Ships within 24hrs.Qty Required 1Kit Contents 2 Arms$729.60 $510.72Fully installed for $1,220.72within 2 weeks - Pre-OrderAvailable for Preorder. Stock due on 6/12/2026.Available for Preorder. Stock due on 6/12/2026.SKU: KTA292 Benefit Note:
A short fall of the modern day IFS 4wd is the adjustment range provided for successful wheel alignments, this becomes even more of an issue when the vehicle is lifted by more than 1 inch. Not only does the vehicle run into camber and caster issues, but ball joint articulation and clearance issues to the coil over strut at ride and droop height. The new Whiteline offset UCA (Upper Control Arm) is an all-in-one solution for any vehicle that has been lifted between 30mm and 70mm. Providing an increase between +2.5 and +3.5 degrees of caster and up to 1.5 degrees of negative camber increase (figures quoted are based off an approximate 50mm/ 2 inch) along with greater clearance to the coil over strut and more articulation of the arm by virtue of new maintenance free GIIRO bushing technology.Front Upper Control Arms Fixed Offset to Suit Volkswagen Amarok 2H 4Motion
ℹ️ Fixed offset alignment correction arms - includes ball jointMaximises tyre contact with the road, improving cornering and grip; the perfect, complete upgrade. Includes: 2 ArmsPre-OrderAvailable for Preorder. Stock due on 6/12/2026.Available for Preorder. Stock due on 6/12/2026.Qty Required 1Kit Contents 2 Arms$729.60 $510.72Fully installed for $1,220.72within 2 weeks - SKU: KTA296 Benefit Note: A short fall of the modern day IFS 4wd is the adjustment range provided for successful wheel alignments, this becomes even more of an issue when the vehicle is lifted by more than 1 inch. Not only does the vehicle run into camber and caster issues, but ball joint articulation and clearance issues to the coil over strut at ride and droop height. The new Whiteline offset UCA (Upper Control Arm) is an all-in-one solution for any vehicle that has been lifted between 30mm and 70mm. Providing an increase between +2.5 and +3.5 degrees of caster and up to 1.5 degrees of negative camber increase (figures quoted are based off an approximate 50mm/ 2 inch) along with greater clearance to the coil over strut and more articulation of the arm by virtue of new maintenance free GIIRO bushing technology.
Front Upper Control Arms Fixed Offset to Suit Isuzu D-Max and Mazda BT-50 2020-on 4wd
ℹ️ Fixed offset alignment correction arms - includes ball jointMaximises tyre contact with the road, improving cornering and grip; the perfect, complete upgrade. Includes: 2 ArmsIn StockShips within 24hrs.Ships within 24hrs.Qty Required 1Kit Contents 2 Arms$854.05 $597.84Fully installed for $1,307.84within 2 weeks - SKU: KTA301 Benefit Note:A short fall of the modern day IFS 4wd is the adjustment range provided for successful wheel alignments, this becomes even more of an issue when the vehicle is lifted by more than 1 inch. Not only does the vehicle run into camber and caster issues, but ball joint articulation and clearance issues to the coil over strut at ride and droop height. The new Whiteline offset UCA (Upper Control Arm) is an all-in-one solution for any vehicle that has been lifted between 30mm and 70mm. Providing an increase between +2.5 and +3.5 degrees of caster and up to 1.5 degrees of negative camber increase (figures quoted are based off an approximate 50mm/ 2 inch) along with greater clearance to the coil over strut and more articulation of the arm by virtue of new maintenance free GIIRO bushing technology.
Front Upper Control Arms Fixed Offset to Suit Nissan Navara D40, D23 and Pathfinder R51
ℹ️ Fixed offset alignment correction arms - includes ball jointDelivers a balanced mix of comfort, precision, and durability; the perfect, complete upgrade. Includes: 2 ArmsIn StockShips within 24hrs.Ships within 24hrs.Qty Required 1Kit Contents 2 Arms$729.60 $510.72Fully installed for $1,220.72within 2 weeksSelect Option To Show Price - SKU: WA395R Benefit Note:
Most would agree that the time and stress to remove and replace bushings and ball joints to suspension arms can be hard to justify. Making up press tools and damaging arms are just two of the problems one can endure. Why put yourself through it when you can purchase complete arms, fitted with market leading Whiteline synthetic elastomer bushings and premium quality ball joints (if applicable).Front Upper Control Arm Right to Suit Ford Falcon FG, FGX and FPV
ℹ️ Replacement and repair upgrade - includes ball jointMaximises tyre contact with the road, improving cornering and grip; the perfect, complete upgrade. Includes: 1 ArmIn StockShips within 24hrs.Ships within 24hrs.Qty Required 1Kit Contents 1 Arm$327.00 $228.90Fully installed for $558.90within 2 weeks - SKU: KTA310 Benefit Note:A short fall of the modern day IFS 4wd is the adjustment range provided for successful wheel alignments, this becomes even more of an issue when the vehicle is lifted by more than 1 inch. Not only does the vehicle run into camber and caster issues, but ball joint articulation and clearance issues to the coil over strut at ride and droop height. The new Whiteline offset UCA (Upper Control Arm) is an all-in-one solution for any vehicle that has been lifted between 30mm and 70mm. Providing an increase between +2.5 and +3.5 degrees of caster and up to 1.5 degrees of negative camber increase (figures quoted are based off an approximate 50mm/ 2 inch) along with greater clearance to the coil over strut and more articulation of the arm by virtue of new maintenance free GIIRO bushing technology.
Front Upper Control Arms Fixed Offset to Suit Toyota Land Cruiser 100 Series IFS
ℹ️ Fixed offset alignment correction arms - includes mounting provisions for OEM ABS lines and AHC ride height sensors - includes ball jointDelivers a balanced mix of comfort, precision, and durability; the perfect, complete upgrade. Includes: 2 ArmsIn StockShips within 24hrs.Ships within 24hrs.Qty Required 1Kit Contents 2 Arms$801.80 $561.26Fully installed for $1,081.26within 2 weeks - SKU: WA378R Benefit Note:
Most would agree that the time and stress to remove and replace bushings and ball joints to suspension arms can be hard to justify. Making up press tools and damaging arms are just two of the problems one can endure. Why put yourself through it when you can purchase complete arms, fitted with market leading Whiteline synthetic elastomer bushings and premium quality ball joints.Front Upper Control Arm Right to Suit Toyota HiLux 2005-on and Foton Tunland 4wd
ℹ️ Replacement and repair upgrade - includes ball jointDelivers a balanced mix of comfort, precision, and durability; the perfect, complete upgrade. Includes: 1 ArmIn StockShips within 24hrs.Ships within 24hrs.Qty Required 1Kit Contents 1 Arm$191.00 $133.71Fully installed for $463.71within 2 weeks - SKU: KTA249 Benefit Note:A short fall of the modern day IFS 4wd is the adjustment range provided for successful wheel alignments, this becomes even more of an issue when the vehicle is lifted by more than 1 inch. Not only does the vehicle run into camber and caster issues, but ball joint articulation and clearance issues to the coil over strut at ride and droop height. The new Whiteline offset UCA (Upper Control Arm) is an all-in-one solution for any vehicle that has been lifted between 30mm and 70mm. Providing an increase between +2.5 and +3.5 degrees of caster and up to 1.5 degrees of negative camber increase (figures quoted are based off an approximate 50mm/ 2 inch) along with greater clearance to the coil over strut and more articulation of the arm by virtue of new maintenance free GIIRO bushing technology.
Front Upper Control Arms Fixed Offset to Suit Toyota FJ Cruiser, Prado 120 150 Series and 4Runner
ℹ️ Fixed offset alignment correction arms - includes ball jointDelivers a balanced mix of comfort, precision, and durability; the perfect, complete upgrade. Includes: 2 ArmsIn StockShips within 24hrs.Ships within 24hrs.Qty Required 1Kit Contents 2 Arms$806.55 $564.59Fully installed for $1,084.59within 2 weeksSelect Option To Show Price - SKU: KTA297 Benefit Note: A short fall of the modern day IFS 4wd is the adjustment range provided for successful wheel alignments, this becomes even more of an issue when the vehicle is lifted by more than 1 inch. Not only does the vehicle run into camber and caster issues, but ball joint articulation and clearance issues to the coil over strut at ride and droop height. The new Whiteline offset UCA (Upper Control Arm) is an all-in-one solution for any vehicle that has been lifted between 30mm and 70mm. Providing an increase between +2.5 and +3.5 degrees of caster and up to 1.5 degrees of negative camber increase (figures quoted are based off an approximate 50mm/ 2 inch) along with greater clearance to the coil over strut and more articulation of the arm by virtue of new maintenance free GIIRO bushing technology.
Front Upper Control Arms Fixed Offset to Suit Holden Colorado RG and Trailblazer
ℹ️ Fixed offset alignment correction arms - includes ball jointMaximises tyre contact with the road, improving cornering and grip; the perfect, complete upgrade. Includes: 2 ArmsIn StockShips within 24hrs.Ships within 24hrs.Qty Required 1Kit Contents 2 Arms$682.10 $477.47Fully installed for $1,187.47within 2 weeksSelect Option To Show Price - Pre-OrderAvailable for Preorder. Stock due on 7/12/2026.Available for Preorder. Stock due on 7/12/2026.SKU: KTA336 Benefit Note:A short fall of the modern day IFS 4wd is the adjustment range provided for successful wheel alignments, this becomes even more of an issue when the vehicle is lifted by more than 1 inch. Not only does the vehicle run into camber and caster issues, but ball joint articulation and clearance issues to the coil over strut at ride and droop height. The new Whiteline offset UCA (Upper Control Arm) is an all-in-one solution for any vehicle that has been lifted between 30mm and 70mm. Providing an increase between +2.5 and +3.5 degrees of caster and up to 1.5 degrees of negative camber increase (figures quoted are based off an approximate 50mm/ 2 inch) along with greater clearance to the coil over strut and more articulation of the arm by virtue of new maintenance free GIIRO bushing technology.
Front Upper Control Arms Fixed Offset to Suit Mitsubishi Pajero NS, NT, NW and NX 2006-on
ℹ️ Fixed offset alignment correction arms - includes ball jointEnhances steering response, delivering sharper handling and more predictable vehicle dynamics; the perfect, complete upgrade. Includes: 2 ArmsPre-OrderAvailable for Preorder. Stock due on 7/12/2026.Available for Preorder. Stock due on 7/12/2026.Qty Required 1Kit Contents 2 Arms$721.05 $504.74Fully installed for $1,024.74within 2 weeks
- Front Upper Control Arms Fixed Offset to Suit Great Wall Ute Cannon and Tank 300 excl Hybrid and Alfa models
- Front Axle Control Arm Upper - Arm Offset Assembly to Suit Mitsubishi Triton MV
- Adjustable Front Upper Control Arms to Suit Toyota FJ Cruiser, Prado 120 150 Series and 4Runner
- Front Upper Control Arms Fixed Offset to Suit Chevrolet Silverado and GMC Sierra 4th Gen
- Front Upper Control Arms Fixed Offset to Suit Mitsubishi Pajero NS, NT, NW and NX 2006-on
- Front Upper Control Arm Right to Suit Ford Falcon FG, FGX and FPV
- Front Upper Control Arms Fixed Offset to Suit Toyota Hilux Rogue and GR
- Front Upper Control Arms Fixed Offset to Suit Holden Colorado RG
- Front Upper Control Arms Fixed Offset to Suit Toyota Land Cruiser 200 Series
- Front Upper Control Arms Fixed Offset to Suit Ford Everest PB, Ranger PY 4x4 and VW Amarok T1
- Front Upper Control Arm Right to Suit Toyota HiLux 2005-on and Foton Tunland 4wd
- Front Upper Control Arms Fixed Offset to Suit Volkswagen Amarok 2H 4Motion
- Front Upper Control Arms Fixed Offset Suit Chevrolet Silverado and GMC Sierra 2nd & 3rd Gen
- Front Upper Control Arm Left to Suit Toyota HiLux 2005-on and Foton Tunland 4wd
- Front Upper Control Arms Fixed Offset to Suit Ram 1500 DT
- Front Upper Control Arms Fixed Offset to Suit Toyota Land Cruiser 300 Series and Prado 250
- Control Arm Lower and Upper - Arm Kit to Suit Ford/FPV Falcon FG, FGX
- Front Upper Control Arms Fixed Offset to Suit Toyota Land Cruiser 100 Series IFS
- Adjustable Front Upper Control Arms to Suit Ford Everest, Ranger PX and Mazda BT-50 UP, UR
- Front Upper Control Arms Fixed Offset to Suit Ford F-150 11th 12th 13 Gen and Expedition 4th Gen
- Front Upper Control Arms Fixed Offset to Suit Toyota FJ Cruiser, Prado 120 150 Series and 4Runner
- Front Upper Control Arms Fixed Offset to Suit Ford F-150 14th Gen
- Front Upper Control Arms Fixed Offset to Suit Isuzu D-Max and Mazda BT-50 2020-on 4wd
- Fixed Rear Upper Control Arms to Suit Ford Mustang SN95
- Adjustable Rear Upper Camber Arms to Suit Toyota Corolla and Yaris GR AWD
- Adjustable Rear Upper Camber Arms to Suit Tesla Model 3 and Model Y
- Adjustable Rear Upper Camber Arms to Suit Honda Civic 10th 11th Gen FC FK FE FL
- Adjustable Rear Traction Arms to Suit Tesla Model 3
- Rear Control Arm Upper Front - Arm to Suit Telsa Model 3, Model Y
- Rear Control Arm Upper - Camber Arms to Suit Ford Falcon/Fairlane BA-FGX, Territory SX-SZ and FPV
- Adjustable Rear Upper Camber Arms to Suit Hyundai I30 incl N, Veloster and Kia Cerato
- Control Arm Lower and Upper - Arm Kit to Suit Ford Falcon FG, FGX and Territory SX-SZ
- Rear Control Arm Upper - Arm to Suit Ford Focus, Mazda3 and Volvo C30, S40
- Rear Control Arm Upper Front - Arm Assembly-Adjustable to Suit Mazda MX-5 ND
- Rear Control Arm Upper Rear - Arm to Suit Telsa Model 3, Model Y
- Adjustable Rear Upper Camber Arms to Suit Audi, Seat, Skoda and Volkswagen PQ35/MQB Fwd/Awd
- Rear Control Arm Upper - Arm to Suit Ford Falcon/Fairlane BA-FGX, Territory SX-SZ and FPV
- Adjustable Rear Upper Camber Arms - Arm to Suit Ford Focus, Mazda3 and Volvo C30, S40
- Rear Control Arm Upper Rear - Arm Assembly-Adjustable to Suit Mazda MX-5 ND
Your vehicle
Don’t know your rego?
Matching vehicles
No match — try selecting it below.
Got your rego handy?
Refine your search
Clear all- Performance Suspension Kits 30
- Lowering Springs 40
- Sway Bars & Sway Bar Kits 627
- Sway Bar Brackets 5
- Sway Bar Relocation Kits 5
- Sway Bar Service Kits 121
- Sway Bar Links 220
- Control Arms 173
- Lower Control Arms 123
- Individual Lower Control Arms 63
- Upper Control Arms 54
- Individual Upper Control Arms 7
- Strut Braces 41
- Suspension Bushes 1843
- Alignment Bushes 155
- Axle Bushes 18
- Coil Spring Spacers, Insulators & Seats 45
- Complete Bushing Kits 102
- Control Arm Bushes 687
- Cross Member Bushes 3
- Differential Bushes 68
- Greasable Shackles & Bushes 18
- Leaf Spring Bushes 192
- Panhard Rod Bushes 41
- Radius Arm Bushes 31
- Shifter Bushes 9
- Shock Absorber Bushes 67
- Strut Rod Bushes 42
- Subframe Bushes 31
- Sway Bar Bushes 423
- Toe Arm Bushes 2
- Traction Control Bushes 2
- Trailing Arm Bushes 130
- Tramp Rod Bushes 1
- Trunnion Bushes 1
- Watts Link Bushes 4
- Lowering Blocks 35
- 4x4 Lift Kits 6
- Diff Drop Kits 7
- Suspension Parts 3106
- Bump Stops 28
- Nuts, Bolts & Screws 2
- Panhard Rods 28
- Struts & Shock Absorbers 28
- Strut Mounts 28
- Suspension Arms 268
- Alignment Arms 24
- Camber Arms 6
- Caster Arms 12
- Toe Arms 9
- Control Arm & Radius Arm Kits 3
- Suspension Arm Service Kits 35
- Ball Joint Replacement Boots 5
- Ball Joint Replacement Kits 10
- Replacement Suspension Arm Bushes 19
- Vertical Stabilizer Links 1
- Suspension Springs 67
- Coil Springs 41
- Raised Springs 1
- Leaf Springs 25
- Fixed Pins 17
- Leaf Spring Shackles 12
- U Bolts 8
- Spring Saddles 1
- Alignment Parts 342
- Camber Bolts 25
- Centre Bearing Alignment 4
- Transmission Parts 13
- Gearbox Mount Bushes 13
- Chassis Parts 61
- Body Mount Bushes 7
- Chassis Bracing & Strengthening Kits 47
- Chassis Braces 6
- Strut Brace Parts 1
- Door Jamb Bushes 1
- Headlight Sensor Brackets 4
- Tailshaft Spacers 2
- Engine Parts 25
- Alternator Bushes 2
- Engine Mount Bushes 23
- Engine Mounts 1
- Steering Parts 101
- Drag Link Bushes 2
- Hicas Lock Kit 1
- Idler Arm Bushes 20
- Idler Arms 1
- Steering Damper Bushes 6
- Steering Knuckles 1
- Steering Rack & Pinion Bushes 59
- Steering Rack Coupling Bushes 7
- Tie Rods 4
- Trailing Arms 34
- Individual Trailing Arms 2
- Radius Arms 18
- Individual Radius Arms 10
- Brakes 9
- ABS Components 2
- Brake Line Kits 3
- Brake Valve Linkage 2
- Handbrake Parts 2
- Universal Parts 324
- Bushing Grease 3
- Polyurethane Rods 7
- Polyurethane Sheets 1
- Trade Packs 14
- Bulk Alignment Shims 4
- Bulk Leaf Spring Bushes 7
- Bulk Shock Absorber Bushes 1
- Bulk Sway Bar Link Bushes 2
- Universal Alignment Shims 10
- Universal Body Mount Bushes 1
- Universal Bump Stops 15
- Universal Camber Bolts 5
- Universal Coil Spring Spacers 33
- Universal High Lift Jack Handle Holders 1
- Universal Leaf Spring Bushes 7
- Universal Lowering Blocks 35
- Universal Pivot Bushes 1
- Universal Shock Absorber Bushes 2
- Universal Steering Coupling Bushes 7
- Universal Strut Brace Parts 1
- Universal Sway Bar Lateral Locks 10
- Universal Sway Bar Link Bushes & Washers 12
- Universal Sway Bar Links 149
- Adjustable Sway Bar Links 53
- Fixed Sway Bar Links 70
- Sway Bar Link Bushes 11
- Sway Bar Link Washers 1
- Threaded Rod Sway Bar Links 14
- Universal Sway Bar Mounts & Brackets 26
- Universal U Bolts 8
- Universal Valve Caps 1
- Merchandise 13
- Accessories 4
- Apparel 3
- Car Stickers 4
- Hats, Caps & Beanies 2
- Automotive Tools 3
- Bushing & Bearing Press Tool Kits 1
- Tyre Pressure Gauges 1
- Wheel Alignment Tools 1
- Car Accessories 4
- Bushing Grease 3
- Valve Caps 1
No categories match.
Can’t find what you’re looking for?
Our team can help you find the right part — or tell us what was missing so we can improve the site.
Call Us (02) 4340 2355 Give Feedback (opens in a new tab)